Showing posts with label marine band. Show all posts
Showing posts with label marine band. Show all posts

Wednesday, February 8, 2017

(Almost) The Last of The Mohicans


While I now tend to favour European transistorized radios made in the 1960’s and 1970’s, I can remember as a kid lusting after shortwave receivers like the Heathkit Mohican. Alas, the price was too high for a teenager with an allowance and no job, so I had to settle for a Knight-Kit Star Roamer at the time.
My Restored Heathkit Mohican GC-1A

Fast forward to last fall, and there was a sad (correction…pathetic) looking wreck of a Mohican GC-1A at a local ham flea market, beckoning to me. For $10, I thought I would take a chance on it, even though the S-meter and antenna were missing and the case and chrome knobs were badly pitted. One promising thing was that the dual sliderule dials were clean and intact, and the tuning knobs and pointers seemed to work OK.




First IF Transformer now shielded
and covering the hole in the board
Opening it up, however, revealed more surprises. There was the first IF transformer, sans outer shield, suspended by a few wires above a gaping hole in the board. Did something explode in there, or did the builder get frustrated and punch a hole through it with a screwdriver? Looking further down the board, I couldn’t help but notice a couple of trimmer pots, also suspended by wires above the board. This was going to require a schematic to figure out what was going on, so I Googled the manual and downloaded it.

Series-resonant 455 kHz filters
(circled)
As I was to discover, someone in their lack of wisdom decided to replace two interstage ceramic IF filters with those trimmer pots (!). But it doesn’t stop there. The AVC switch and the dial lights were also miswired. It dawned on me that someone with just enough knowledge to be dangerous must have had a go at this radio as a second or third owner, because the construction was otherwise  good. Maybe when they discovered that pots don’t work well as bandpass filters, they decided to take revenge on the IF transformer? While I didn’t have any three-terminal ceramic filters on hand, I did have some series-resonant two-terminal types that I used as interstage couplers in those same locations. Result.

Battery Pack
So, after sanding down the steel case, priming it, and applying several coats of an automotive aerosol paint (guesswork involved on the original colour), it looks great. Surprisingly, the knobs cleaned right up with a damp cloth, and continue to shine like new. Of course, the battery pack was somewhat corroded, but now functions well. With 8 C cells loaded, I have to say this radio weighs enough to make a good negative-buoyancy marine stabilizer (boat anchor), thanks largely to the steel construction.

S-Meter & AVC Switch
Getting original components is near impossible, so I settled on a replacement telescoping antenna, and had to enlarge the S-meter opening slightly to accommodate one from a cannibalized CB set. To make the meter function logically and properly, I had to reverse the scale card inside the meter and pad it down with a shunt resistor.

Apart from re-capping, one of the last tasks was alignment. Heathkit includes an involved procedure in their manual, and it’s worth following. The only oddity is that the IF tuned fine at 435 kHz, but I couldn’t get it to go to 455 kHz. This caused a bit of head scratching when it came to identifying the image frequencies, but as long as the alignment is done with this knowledge, it’s not a problem.

After completing the alignment, it was time to hoist the antenna and play. Intially, I was disappointed with the gravelly quality of the audio, and SSB sounded somewhat unintelligible at times. My first thought was that the IF alignment was poor and/or the BFO needed tweaking. With no joy there, I looked at the Mohican’s demodulated audio from my RF generator on the ‘scope, and noticed crossover distortion at the speaker. By padding the bias resistors on the bases of the push-pull audio output transistors, the sound is now quite sweet on both AM and SSB. It took a lot of padding, though, so the old germanium transistors were probably getting a bit tired.
Alignment trimmer caps and coils for local oscillator, mixer and front end


Heathkit marketed this radio from the early 1960’s up until about 1968. While it’s not the hottest receiver by today’s standards, it is surpisingly sensitive and stable. That probably explains how this single model remained popular througout nearly a decade. And while I lived with its challenges for several months, now that it is fully functional, the nostalgic value is going to keep it in my collection for some time to come.

Tuesday, January 27, 2015

NORDMENDE GLOBETRAVELER II

I like Nordmende. Their radios just seemed to ooze quality. The Globetraveler series exemplified that. It is the epitome of what was considered a high end portable radio in the late 1960s: well built, beautiful sounding and feature-laden.
Nordmende Globetraveler II

At the time, the Globetraveler would have been way out of my league in terms of affordability. Besides, I was just a kid then. Today, however, a gently used version can be found online quite cheaply. With a little bit (hopefully) of effort, it can be made to look and run like new.

Such is the case with my Globetraveler II. It's the North American equivalent of the European Globetrotter TN6000. Its best feature is a bandspread tuner that allows you to tune specific shortwave broadcast bands individually and comfortably without the "touchiness" of a tuner that covers all bands in a single sweep of the dial. These bands range from 13m to 80m. Not sure why they included an amateur radio band, because as far as I know, broadcasting never took place in the 80m band.
 
Besides the need for cosmetic cleaning, here were the issues with mine:
  • Shortwave bandspread tuner non-functional on some bands and band switching was noisy. This was major for me, as the bandspread tuner was what set this radio apart from many others.
  • Audio was slightly distorted (crossover distortion).
  • The a.c. socket uses a silly switch that cuts out the battery when an a.c. cord is plugged in. Silly because the lever that actuated the switch often stuck, cutting out the batteries even when the cord was pulled.
  • Power supply needed re-capping. No surprise there after 45 years, but ripple persists. Since I prefer battery power, this is not a big deal for me, but I suspect a leaky diode or two in the bridge rectifier. Later.
  • A dangerous carry handle that likes to unhook easily on its own. Caution with this one!
The bandspread tuner was not an easy fix. The first approach is always to try to clean all switches. I used a run-of-the-mill switch and potentiometer cleaner on the tuner's wafer sections. Big mistake. The tuner became less and less functional the more I sprayed until it totally failed. By this point, my mind went straight to the hardest solution, and I began to believe the local oscillator stage failed. The thought of accessing this tiny board gave me a slap of reality, and I bit the bullet and bought a decent but expensive cleaner (DeOxit). A couple of sprays later, it came back to life. The wires in this tuner are very delicate, so after I discovered a wire I had broken when probing the tuner, all bands worked again. After the cleaner dried, I re-tuned as many coils as I could access. This tuner is designed for manufacturing, not service. Access to components is sometimes horrible - a nightmare in fact (see photo).
Bandspread tuner from hell

Fixing the audio issue was easy. De-solder a jumper, insert ammeter, and tweak the output stage bias until about 6mA is achieved.

Finally, as with other radios reviewed here, I performed a subjective comparison with my old stalwart kitchen radio - the Telefunken Partner 500.

First off, I must say that in terms of sound quality, the Globetraveler is in a different league due to its size relative to the Partner. No surprise - the bass presence is noticeably better on the Globetraveler. Another advantage it has is separate bass and treble controls, compared to the Partner's tone control.

In terms of FM performance, the sensitivity was only marginally better on the Globetraveler. In urban areas with telescopic antenna up, both radios suffered from overload. This resulted in distorted images of strong stations appearing in other places on the dial, interfering with weaker stations.

With the antenna up on the Globetraveler, it was noted that on certain shortwave bands there was some feedthrough of FM signals. I suspect this wouldn't be a problem once outside of town. Interestingly, the Globetraveler has a segmented antenna, giving about an extra foot if needed in fringe areas. Comparing the two radios on the 19m and 49m bands, it was hard to tell if there was a difference in sensitivity. The difference, of course is in the ease of tuning in stations with the Globetraveler's bandspread tuner. I also suspect (but have not verified) that the Globetraveler has better image rejection due to its more sophisticated tuner with separate front end tuning coils for each band.

The Partner holds up surprisingly well against the Globetraveler in terms of basic performance, but the Nordmende definitely is much more pleasurable to use and listen to.

Some other Globetraveler features to point out:
  • Sensitive tuning meter on all bands.
  • Inclusion of a Marine Band (1.5 to 3.5 MHz), although it's not used much for this purpose these days.
  • Long wave band, also useless in North America.
  • AM (BC) band, which uses an internal loopstick antenna.
  • External antenna connection, which helps shortwave performance significantly.
  • Operates from 5 "D" cells (7.5V).
The Globetraveler II is definitely the flagship of my "kofferradio" fleet. Can't wait for warmer weather to take it outside and test it outside of the city.